Guangzhou Liwin Electronic Technology Co., Ltd.

HID Xenon Installation Guide

From: HID Xenon Installation Guide
publisher: HID Xenon Installation Guide
Time: 2014-07-24
Summary: HID Xenon Installation Guide
HID Xenon Installation Guide 
 
Graphic installation steps (see comparison picture view) 
①. Before conversion to car headlights turned off, upon cooling the lamp bulb to remove the original car's power outlet 
②. Fixed Loosen the clamp and remove the halogen bulb, the same model accidentally swapped HID bulbs (usually H1, H4, H7, 9005,9006 see all models with light table), the lamp fixture fixed, HID bulbs and power lines stretched outside the headlight assembly. 
③. Would HID lamp ballast fixed position near the headlight assembly for easy wiring (wiring convenient, well-ventilated, avoid close to the engine, radiator and other objects), each ballast requires at least two screws. 
④. Before-wiring power lines, the power lines of yin and yang, head into the locked position AMP dedicated connector to prevent high pressure fittings water. Then pick the low-pressure line (DC 12V), red wire headlight power outlet positive, black line (blue line) connected to a power outlet headlights negative, then no less than four of each heat tape wrapped joints and nylon Zhasi (HID light box with 6) to secure the line to avoid friction and the surrounding metal. 
⑤. All after installation, clean up the installation site, check the height of the light through the lights experiment, adjusted to the proper position lights. 
___________________________________________________________________________________
Attachment: five steps to install the law: 
Five step conversion xenon lamp 
     Generally modified a car xenon lamp time as long as an hour. Process is not too complicated, a simple modification xenon lamp as follows: 
     One, first select the xenon lamp models, the original headlight bulbs removed intact. 
     Second, installing fixed xenon lamp bulb. 
     Third, find a place to put a fixed xenon lamp ballasts, pay attention to the heat, to ensure that the temperature is not too high. 
     Fourth, the power supply and lighting ballast power connector, an output line ballast and xenon lamp bulb MP interfaces are connected. 
     Fifth, adjust the focus xenon lamp. 
     Modified xenon lamp has three considerations: 
     First, you want to choose a professional auto service shop, so as to ensure that the conversion process professional operation will not affect the lamp life. 
     Second, many owners on a deep understanding of the xenon lamp, the owners according to their economic capacity to choose. 
     Third, before deciding to buy Xenon headlights of the vehicle to confirm their model, each brand has a different model, be aware of the major car
HID Xenon Installation Guide 
 
Graphic installation steps (see comparison picture view) 
①. Before conversion to car headlights turned off, upon cooling the lamp bulb to remove the original car's power outlet 
②. Fixed Loosen the clamp and remove the halogen bulb, the same model accidentally swapped HID bulbs (usually H1, H4, H7, 9005,9006 see all models with light table), the lamp fixture fixed, HID bulbs and power lines stretched outside the headlight assembly. 
③. Would HID lamp ballast fixed position near the headlight assembly for easy wiring (wiring convenient, well-ventilated, avoid close to the engine, radiator and other objects), each ballast requires at least two screws. 
④. Before-wiring power lines, the power lines of yin and yang, head into the locked position AMP dedicated connector to prevent high pressure fittings water. Then pick the low-pressure line (DC 12V), red wire headlight power outlet positive, black line (blue line) connected to a power outlet headlights negative, then no less than four of each heat tape wrapped joints and nylon Zhasi (HID light box with 6) to secure the line to avoid friction and the surrounding metal. 
⑤. All after installation, clean up the installation site, check the height of the light through the lights experiment, adjusted to the proper position lights. 
___________________________________________________________________________________
Attachment: five steps to install the law: 
Five step conversion xenon lamp 
     Generally modified a car xenon lamp time as long as an hour. Process is not too complicated, a simple modification xenon lamp as follows: 
     One, first select the xenon lamp models, the original headlight bulbs removed intact. 
     Second, installing fixed xenon lamp bulb. 
     Third, find a place to put a fixed xenon lamp ballasts, pay attention to the heat, to ensure that the temperature is not too high. 
     Fourth, the power supply and lighting ballast power connector, an output line ballast and xenon lamp bulb MP interfaces are connected. 
     Fifth, adjust the focus xenon lamp. 
     Modified xenon lamp has three considerations: 
     First, you want to choose a professional auto service shop, so as to ensure that the conversion process professional operation will not affect the lamp life. 
     Second, many owners on a deep understanding of the xenon lamp, the owners according to their economic capacity to choose. 
     Third, before deciding to buy Xenon headlights of the vehicle to confirm their model, each brand has a different model, be aware of the major car

Guangzhou Liwin Electronic Technology Co., Ltd

Previous:Largest HID xenon lamp exporter in Asia

Next:HID lights dimming technology brief